Alloysafe.com

Skip to Main Content »

Search Site

Category Navigation:

You're currently on:

Pentek Fibredyne ELPC-30 Water Filter (1 Case / 30 Filters)

Double click on above image to view full picture

Zoom Out
Zoom In

Pentek Fibredyne ELPC-30 Water Filter (1 Case / 30 Filters)


Email to a Friend

Be the first to review this product

Availability: In stock.

$749.99
Add Items to Cart Add to Cart
OR

Quick Overview

Pentek Fibredyne ELPC-30 Water Filter (1 Case / 30 Filters) is manufactured with Dimensions: 30" x 2-7/8" (762 mm x 73 mm), Initial _P (psi) @ Flow Rate (gpm): 3.4 psi @ 3 gpm (0.2 bar @ 11.4 Lpm), Temperature Rating: 40ºF to 180ºF (4.4ºC to 82.2ºC) and Micron Rating (Nominal): 7. The incorporation of best technology makes it best for all electroplating solutions without causing any bleeding of carbon fines into the plating bath. This product uses the carbon that is ultra-clean and highly purified carbon while ensuring prevention of sulfur leaching into the plating bath. Due to fibrous physical structure and manufacturing process, these filters are provided with superior dirt holding ability that offers true depth filtration. True depth filtration offers maximum treatment with minimum pressure drop through the cartridge. End cap gaskets are molded permanently onto the end caps to ease in change-out of filter cartridges. Other advanced features include Bonded PAC Filter Media, Polypropylene End Caps, Polyethylene Netting and Santoprene Gasket.
Pentek Fibredyne ELPC-30 Water Filter (1 Case / 30 Filters) is manufactured with Dimensions: 30" x 2-7/8" (762 mm x 73 mm), Initial _P (psi) @ Flow Rate (gpm): 3.4 psi @ 3 gpm (0.2 bar @ 11.4 Lpm), Temperature Rating: 40ºF to 180ºF (4.4ºC to 82.2ºC) and Micron Rating (Nominal): 7. The incorporation of best technology makes it best for all electroplating solutions without causing any bleeding of carbon fines into the plating bath. This product uses the carbon that is ultra-clean and highly purified carbon while ensuring prevention of sulfur leaching into the plating bath. Due to fibrous physical structure and manufacturing process, these filters are provided with superior dirt holding ability that offers true depth filtration. True depth filtration offers maximum treatment with minimum pressure drop through the cartridge. End cap gaskets are molded permanently onto the end caps to ease in change-out of filter cartridges. Other advanced features include Bonded PAC Filter Media, Polypropylene End Caps, Polyethylene Netting and Santoprene Gasket.
Pentek Fibredyne ELPC-30 Water Filter Cartridge Specs:
Dimensions: 30" x 2-7/8" (762 mm x 73 mm)
Micron Rating (Nominal): 7
Initial _P (psi) @ Flow Rate (gpm): 3.4 psi @ 3 gpm (0.2 bar @ 11.4 Lpm)
Temperature Rating: 40ºF to 180ºF (4.4ºC to 82.2ºC)
Pentek Fibredyne ELPC-30 Electroplating Solutions Filter Materials of Construction:
Filter Media: Bonded PAC
End Caps: Polypropylene
Netting: Polyethylene
Gasket: Santoprene
Pentek Fibredyne ELPC-30 Water Filter Instructions:

NOTE: Cartridges will contain a very small amount of carbon fines (very fine black powder) and a new cartridge after installation should be flushed with sufficient water to remove all traces of the fines from your water system before using the water. Each time you use your filtered water tap for drinking or cooking purposes it is recommended that you run (flush) the tap for at least 20 seconds prior to using water.

NOTE: Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health-related contaminant reduction claims.
NOTE: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Product Tags

Add Your Tags:
Use spaces to separate tags. Use single quotes (') for phrases.
 

My Cart

You have no items in your shopping cart.

Compare Products

You have no items to compare.