Alloysafe.com

Skip to Main Content »

Search Site

Category Navigation:

You're currently on:

"C" Style Aluminum Clamp SV-6 Self Piercing 1/4" Saddle Valve

Double click on above image to view full picture

Zoom Out
Zoom In

"C" Style Aluminum Clamp SV-6 Self Piercing 1/4" Saddle Valve


Email to a Friend

Be the first to review this product

Availability: In stock.

$6.99
Add Items to Cart Add to Cart
OR

Quick Overview

The SV-6 is a C-style self piercing saddle valve equipped with 1/4" male compression fitting. This SV-6 C-frame saddle fits on 3/8" - 5/8" copper tubing and is a good time saver for installers. One can connect it to 1/4" outside diameter tubing with the help of 1/4" take-off compression nut.
After the cold water shut-off valve, install "C" Style aluminum clamp SV-6 self piercing 3/8" saddle valve in-line. For your new RO system, this is the "OFF" position. This C-Style aluminum clamp SV-6 self piercing 1/4" saddle valve can be opened and turn on this saddle tapping valve by turning it counter clock wise. Mount and tighten the self piercing valve on the copper line in an easy to reach place.
Turn the saddle valve clockwise all the way in. This drives the sharp end of a sharp metal pierce into the copper tubing and will pierce a tiny hole. This saddle tapping valve can’t be used for the installation on flex line tubing. Always make sure not to turn valve handle before or at the time of installation of saddle-tapping valve.
The SV-6 is a C-style self piercing saddle valve equipped with 1/4" male compression fitting. This SV-6 C-frame saddle fits on 3/8" - 5/8" copper tubing and is a good time saver for installers. One can connect it to 1/4" outside diameter tubing with the help of 1/4" take-off compression nut.
After the cold water shut-off valve, install "C" Style aluminum clamp SV-6 self piercing 3/8" saddle valve in-line. For your new RO system, this is the "OFF" position. This C-Style aluminum clamp SV-6 self piercing 1/4" saddle valve can be opened and turn on this saddle tapping valve by turning it counter clock wise. Mount and tighten the self piercing valve on the copper line in an easy to reach place.
Turn the saddle valve clockwise all the way in. This drives the sharp end of a sharp metal pierce into the copper tubing and will pierce a tiny hole. This saddle tapping valve can’t be used for the installation on flex line tubing. Always make sure not to turn valve handle before or at the time of installation of saddle-tapping valve.
  • SV-6 Assemble Saddle-Tapping Valve Assembly on Tube Instructions:


  • Hold back plate against tube.


  • Hold valve saddle against tubing in a position directly opposite back plate.


  • Tighten screw enough so valve saddle and back plate are held securely against tube.


  • Tighten screw firmly. Do not crush tube.






  • SV-6 Connect Source Water Feed Tubing to Valve Body Using Compression Fitting Instructions:


  • Slide nut and sleeve onto tubing (in that order).


  • Install insert into plastic tubing.


  • Install tube with insert and sleeve into valve body.


  • Thread compression nut onto valve body. Tighten.


  • Turn saddle-tapping valve handle clockwise until it is firmly seated and piercing lance is fully extended.


  • CAUTION: Supply line is pierced and valve is closed. Do not open valve until system is activated. Turn on cold water supply. Check saddle-tapping valve installation for leaks. Allow water to run from faucet for a few minutes to clear any debris in the line caused by installation.


  • NOTE: If flow from sink faucet is reduced, clean faucet aerator.


Product Tags

Add Your Tags:
Use spaces to separate tags. Use single quotes (') for phrases.
 

My Cart

You have no items in your shopping cart.

Compare Products

You have no items to compare.